What specifications and standards are generally required for industrial wastewater treatment projects?

Thread Content

What specifications and standards are generally applied in industrial wastewater treatment projects from design to final acceptance? There is a wastewater treatment project for a chemical storage tank area; the treatment units are constructed of steel-concrete and steel structures, and the main equipment includes fans, pumps, dehydrators, etc. In addition to complying with the specifications listed below, what other specifications and standards must this project adhere to? Or which of the following standards do not need to be implemented, or are there updated versions? I hope experienced colleagues can help solve this problem; thank you very much :) (1) System design and environmental standards: “Environmental Protection Law of the People’s Republic of China”, issued by Decree No. 22; “Law of the People’s Republic of China on the Prevention and Control of Environmental Pollution by Solid Wastes”, issued by Decree No. 58; “Law of the People’s Republic of China on the Prevention and Control of Air Pollution”, issued by Decree No. 32; “Comprehensive Discharge Standards for Wastewater” GB8978－1996; “Ambient Air Quality Standards” GB3096-1996; “Provisions on Environmental Protection Design for Construction Projects in China” (87) Guohuan Zi No. 002; “Regulations on the Management of Environmental Protection for Construction Projects”, issued by a decree of the State Council on November 18, 1998; “Hygienic Standards for the Design of Industrial Enterprises” GBZ1-2002; “Noise Standards at the Boundaries of Industrial Enterprises” GB12348-90; “Code for Fire Protection Design of Buildings” GB50016-2006; “Fire Protection Law of the People’s Republic of China” (No. 4); “Code for Fire Protection Design of Petrochemical Enterprises” GB50160-92 (1999 edition); “Code for Design of Outdoor Drainage Systems” GB50014－2006; “Code for Design of Water Supply and Drainage Structures” GB50069－2002; “Code for Design of Building Foundations” GB50007-2002. (2) Standards for electrical and instrumentation design: “Code for Design of Power Supply and Distribution Systems” GB50052-95; “Specifications for the Selection of Automation Instruments” HG/T20507-2000; “Provisions for Power Supply Design of Instruments” HG/T20509-2000; “Provisions for Grounding Design of Instrumentation Systems” HG/T20513-2000; “Provisions for the Design of Control Rooms” HG/T20508-2000; “Provisions for the Design of Signal, Alarm, and Safety Interlock Systems” HG/T20511-2000; “Code for Lightning Protection Design of Buildings” GB50057-94 (revised in 2000); “Design of Lighting in Industrial Enterprises” GB50034-92. (3) Construction and installation specifications and standards: “Code for Construction Quality and Acceptance of Steel Structure Projects” GB50205-2001; “Operating Procedures for Anti-corrosion Engineering Construction” YSJ411-89; “Operating Procedures for Structural Installation Project Construction” YSJ404-89; “Requirements for the Construction and Installation of Instruments” HG/T20637.4-1998; “Steel Welded Atmospheric Pressure Vessels” JBT4735-1997; “Quality Inspection and Evaluation Standards for the Construction of Chemical Equipment Installation Projects” HG20236-93; “Code for Construction Quality Acceptance of Concrete Structure Projects” GB50204-2002; “General Specifications for the Construction and Acceptance of Chemical Machinery Installation Projects” HG20203-2000; “Specifications for the Construction and Acceptance of Chemical Tower-type Equipment” HGJ 211-1985; “General Specifications for the Construction and Acceptance of Mechanical Equipment Installation Projects” GB50231-98; “Specifications for the Construction and Acceptance of Compressor, Fan, and Pump Installation Projects” GB50275-98; “Code for Construction Quality Acceptance of Building Water Supply, Drainage, and Heating Projects” GB50242-2002; “Specifications for the Construction and Acceptance of Water Supply and Drainage Pipeline Projects” GB50268-97; “Specifications for the Construction and Acceptance of Welding of Industrial Pipelines for On-site Equipment” GB50236-98; “Specifications for the Construction and Acceptance of Electrical Installation Projects in China” GBJ232-82; “Technical Regulations for Ventilation Ducts” JGJ141-2004. (5) Standards for labor safety design: “General Principles for Safety and Hygiene Requirements in the Production Process” GB12801-91; “Provisions on Labor Safety and Health Supervision for Construction Projects (Engineering Projects)”, Decree No. 3 of the Ministry of Labor; “Guidelines for Safe Design of Electrical Equipment” GB4064-83; “Code for Noise Control Design in Industrial Enterprises” GBJ87-85; “Safety Distances for Mechanical Protection” GB12265-90. This post was last edited by yyong110 on July 3, 2008, at 13:26.]