What tools are needed to set up an instrument repair workshop? ?

2009-02-20View Original

Thread Content

I need a detailed list! Thank you! ! ! ! ! ! ! ! ! !

Reply #22009-02-20

List of Instrument Repair Tools
Serial Number | Item Name | Specification/Model | Unit
1 | Set of double-ended wrenches | 8-piece set | Set
2 | Socket wrenches | 28-piece set | Set
3 | Heavy-duty socket wrenches | 26-piece set | Set
4 | Hex keys | 8-piece set | Set
5 | Pipe wrenches | 350 pieces |
6 | Pipe wrenches | 400 pieces |
7 | Pipe wrenches | 600 pieces |
8 | Pipe wrenches | 900 pieces |
9 | Chain pipe wrenches | 300 pieces |
10 | Chain pipe wrenches | 900 pieces |
11 | Set of universal wrenches | 10-piece set | Set
12 | Snap ring pliers (for straight holes and shafts), length 175 | Pieces |
13 | Snap ring pliers (for curved holes and shafts), length 175 | Pieces |
14 | Explosion-proof hammers | 200, 250 pieces |
15 | Explosion-proof round hammers | 0.45 Kg each |
16 | Explosion-proof octagonal hammers | 4.5 Kg each |
17 | Hand-cranked oil pumps HX-3 | Units |
18 | Dial gauges (0 – 10 mm range) | Units |
19 | Magnetic gauge bases | Units |
20 | Chain guides (2 tons, L=2.5m) | Units |
21 | Tap sets with nominal diameter 6–20, coarse thread | Pieces |
22 | Tap sets with nominal diameter 6–20, fine thread | Pieces |
23 | Tap wrenches with length 280 | Pieces |
24 | Tap wrenches with length 480 | Pieces |
25 | Flat files with straight edges for fitters | 200 pieces |
26 | Flat files with pointed edges for fitters | 200 pieces |
27 | Square files for fitters | 200 pieces |
28 | Triangular files for fitters | 200 pieces |
29 | Round files for fitters | 200 pieces |
30 | Three-jaw clamps (5 T, 10 T) | Units |
31 | Hydraulic three-jaw clamps (15 T) | Units |
32 | Marking rulers | 300 pieces |
33 | Scribing rules | 500 pieces |
34 | Jacks (10 T) | Units |
35 | Jacks (20 T) | Units |
36 | Jacks (32 T) | Units |
37 | Electric drills (∮13) | Pieces |
38 | Angle grinders SIM-125 | Units |
39 | Electric hammers (∮26mm) | Units |
40 | Steel tape measures (3m) | Pieces |
41 | Steel tape measures (5m) | Pieces |
42 | Leather tape measures (50m) | Pieces |
43 | Steel rulers (150, 300, 500, 1000 mm) | Pieces |
44 | Right-angled rulers (315×200 mm) | Pieces |
45 | Vernier calipers (150, 200 mm) | Pieces |
46 | Outside diameter micrometers (0–25; 175–200 mm) | Pieces |
47 | Inside and outside calipers | 400 pieces |
48 | Thread templates (55 degrees, 60 degrees) | Pieces |
49 | Roped steel cables (∮12×1m) | Pieces |
50 | Roped steel cables (∮12×2m) | Pieces |
51 | Roped steel cables (∮12×3m) | Pieces |
52 | Roped steel cables (∮14×2m) | Pieces |
53 | Roped steel cables (∮16×2m) | Pieces |
54 | Roped steel cables (∮16×3m) | Pieces |
55 | U-bolt pins with thread diameter M20 | Pieces |
56 | U-bolt pins with thread diameter M30 | Pieces |
57 | Bolts for wire rope clamps (diameter M12) | Pieces |
58 | Bolts for wire rope clamps (diameter M14) | Pieces |
59 | Levers (∮25, L=500) | Pieces |
60 | Levers (∮32, L=1000) | Pieces |
61 | Round hammers (0.45 Kg) | Pieces |
62 | Octagonal hammers (4.5 Kg) | Pieces |
63 | Copper hammers (1.0 Kg) | Pieces |
64 | Copper hammer (2.5 Kg) | 1 piece |
65 | Infrared thermometers | Units |
66 | Fuel tanks (10L) | Units |
67 | Aluminum alloy elevators (4m, 10m) | Units |
68 | Multifunctional process calibration instrument Fluke744 | Units |
69 | Signal generators, York MC2 multifunctional testers | Units |

Reply #32009-02-20

I think :victory: a multimeter :victory: together with the appropriate taps and wrenches, plus insulating tape, is basically enough to take care of everything

Reply #42009-02-20

Would it be better to list some better-quality tool manufacturers, so that they can be considered when making purchases?

Reply #52009-02-20

In the past, I would bring a small flathead screwdriver with me when I went to the site. :Lol, I even brought a 10-inch adjustable wrench. At this moment, those who are at the site using various hand controllers have their equipment carried on their backs by assistants.

Reply #62009-02-20

The most commonly used ones are: multi-functional tester, screwdriver, wrench, needle-nose pliers

Reply #72009-02-21

I think FLUK 789 is pretty good!

Reply #82009-02-23

How can one identify a repair shop by looking at the list? Hehe, I usually take a multimeter and a few common screwdrivers when I go to the site~~

Reply #92009-02-23

For electronic meters, I know that the FLUKE product line is quite good; aside from the desktop multimeters (I can’t remember the model), Agilent meters are also excellent

Submit a Project

**Looking for Chemical Technology, Equipment & Solutions?** No Registration Required Broader Platform Exposure | Global Chemical Service Provider Connections

Submit Request — Free Consultation

Disclaimer

This is an automated machine translation of the original thread. Some technical terms may have inaccuracies; the original text shall prevail. Click "View Original" at the top right to access the source page, which supports IP-based automatic real-time language translation. Please watch out for contact details and sales inducements to prevent fraud. All content and translations are for reference only, representing solely the poster's personal views. For enquiries, email service@hcbbs.com.

Quick Links