Dust removal treatment for the boiler induced draft fan impeller

We all use boiler soot removers

Why isn’t anyone answering? ? ? ! ! !

High-temperature dusty flue gas passes through a multi-tube cyclone dust remover, after which the amount of dust in the gas is very low. As LZ said, the dust level is high, so efforts should be made on the dust collector itself. The dust removal efficiency of multi-tube cyclones should be relatively high; it is recommended to review the equipment selection and operating parameters. This is a quite critical step; if the dust removal is inadequate and large amounts of dust end up in the water, treating the graywater becomes quite troublesome. Also, check the washing function and effectiveness of the washing device. After desulfurization, it reaches the induced draft fan. As long as the clothing issue is resolved, the problem with the exhaust fan will be solved as well.

For our small chain furnace, we have used car wash nozzles to clean the impeller of the exhaust fan on several occasions, and the results have been satisfactory

1. What if a high-pressure cleaning gun is used? 2. Is it necessary to perform dynamic balancing again after each dust cleaning?

The best approach is to solve the ash removal problem, that is, to address the efficiency issue of multi-tube dust removal. Solving the problem with the fan blades is only a superficial solution; our company has also encountered similar issues, which relate to the need for maintainability of the multiple pipes

It seems there are manufacturers that produce ash removers (in powder form) specifically for coal-fired boilers; these can be added directly to the coal, but it’s not clear what the effect of this is. You can look it up online.

First, I need to know what size boiler the original poster has; it would be best if they could provide a layout diagram with the dimensions, so that I can truly help them solve the problem.

Cleanliness means being obsessed with cleanliness, reaching the extreme level of purity, almost sacred in terms of cleanliness. Committed to promoting more environmentally friendly cleaning methods in China, so as to reduce the use of chemicals worldwide! ! ! Jiepi Cleaning – based in Xi’an, serving clients across the country. We have been dedicated for a long time to the sales and support of German ICS dry ice cleaning machines and dry ice pelletizing machines ； Industrial cleaning system solutions tailored for mechanical automation, as well as dry ice cleaning services. Nationwide convenient cleaning demonstrations available; free demonstrations at any facility~ No obstacles for any outdoor construction work! Free phone demonstration available at any time~ Intelligent dry ice cleaning solutions, on-site dry ice cleaning services, and technical consulting for dry ice cleaning. Power industry: I. External water-free cleaning of the heat dissipation tubes in boiler water wall, convection chambers, air preheaters, superheaters, economizers, etc., can significantly improve the heat exchange efficiency of boilers. II. The slip rings of wind turbine pitch control motors, as well as the carbon powder surrounding them, the gearbox radiators, generator coolers, inverters, etc., are cleaned without water use; this helps to extend the service life of the equipment, reduce failure rates, and significantly increase the operating time of power generation equipment. III. The finned tubes in the air-cooling island of air-cooled units are affected by fibrous contaminants such as plant fluff; it is difficult to clean them thoroughly using conventional water jet methods, while dry ice cleaning can address this issue more effectively. IV. Conducting a water-free cleaning of the external ash accumulation on the superheaters, evaporators, and economizer finned tubes of the kiln head and kiln tail boilers used for waste heat power generation can significantly improve heat exchange efficiency and enhance economic benefits. Petroleum industry: Cleaning the ash and soot from the outer walls of various heaters, air preheaters, and convective chamber tube banks in refineries can reduce flue gas temperature and lower energy consumption. On-site dry ice cleaning available: pre-procedures for painting and final assembly, as well as special paint removal services. On-site dry ice cleaning is available to remove soot accumulated on wood, bricks, concrete, and metal objects resulting from fires, as well as the burn marks left behind. We provide on-site dry ice cleaning services for printers, pharmaceutical factories, food processing plants, high-end manufacturing industries, railways, outdoor construction projects, and various other applications where it is difficult to clean visible areas without the need for disassembly. We offer on-site dry cleaning services for ancient relics, ceramics, airport runways, high-end wooden products, and complex equipment. Dry ice cleaning services are available on-site; we clean dust buildup from tungsten inert gas welding furnaces, RTO furnaces, and waste heat boilers – all without water and without the need to disassemble the furnaces. Address: No. 1518, Hongye 1st Road, Caotan Economic Development Zone, Xi’an. Contact person: Manager Chen, phone number: 13119108126. Email: 13119108126@163.com. China: http://www.sxcleanliness.com. Germany: https://www.ics-dryice.com