100 examples of unsafe behaviors by general workers

Thread Content

1. Failing to wear a safety helmet properly as required when entering the work area； 2. Failure to wear protective clothing that meets safety standards during work ； 3. The protective clothing does not fit properly ； 4. Failing to repair work uniforms promptly when they become damaged, and failing to clean them thoroughly when they get oily ； 5. Work in slippers at the job site ； 6. Do not wear safety shoes when working in designated areas or on tasks of certain types ； 7. Working bare-chested in hot climates ； 8. During hot work, the collars, cuffs, trouser legs, and shoelaces are not properly fastened ； 9. Failing to wear a safety belt when working at heights ； 10. Failing to wear gloves during assembly work ； 11. Failing to wear safety goggles during grinding operations ； 12. Wear gloves when operating rotating machinery ； 13. Wear gloves when using a sledgehammer ； 14. Failing to wear safety goggles during gas welding and cutting operations ； 15. Do not use protective masks during welding operations ； 16. No protection measures have been taken against harmful light, radiation, and noise ； 17. Talk to people who are working ； 18. In the event of an accident, gather at the scene of the incident ； 19. Riding a bike inside the factory with passengers ； 20. Entering the construction site or starting work while under the influence of alcohol ； 21. Spitting anywhere ； 22. Smoking in non-designated areas or smoking while walking ； 23. Fighting and playing around in the work area during working hours ； 24. Railway level crossings and trains passing through ahead ； 25. Talking in the middle of the road ； 26. Working in low-light conditions ； 27. Lack of concentration when operating mechanical equipment ； 28. Failing to attend safety education or training on time ； 29. Failing to conduct safety checks on the construction site ； 30. Unclear handover of tasks ； 31. Climbing a ladder up and down with one hand ； 32. Remaining on high edges without fall protection measures ； 33. Failing to properly store tools and workpieces used in work at heights ； 34. Pass under the crane’s load ； 35. Failing to avoid workers on the ground when lifting objects ； 36. Entering a dangerous area despite others’ warnings ； 37. Entering a hazardous area despite hazard signs ； 38. Enter other work sites at will ； 39. Do not touch unfamiliar machinery, devices, and control switches casually ； 40. Removing safety warning signs without permission ； 41. Removing or adding lifting plates without permission ； 42. No fall prevention measures are taken when cutting waste material at heights or using construction accessories ； 43. No fall prevention measures were taken after temporary manholes and material access holes were created ； 44. Engaging in special operations without proper licenses ； 45. Failing to conduct a safety check on the tools to be used before starting work ； 46. Using tools and equipment that are not meant for one’s own use ； 47. Failing to carry out lifting operations in accordance with the instructions of the supervisor ； 48. Remove the safety devices from the tools used privately ； 49. Use open-flame lighting in enclosed spaces ； 50. Place construction accessories and finished products randomly ； 51. Carrying out construction in a reckless manner, ignoring the proper procedures ； 52. Proceed with construction when the conditions are not yet ripe ； 53. The working posture is suboptimal ； 54. Excessive force or uncoordinated movements when performing tasks ； 55. Transporting tools and workpieces by throwing ； 56. Impacting pressurized industrial gas cylinders ； 57. Use acetylene cylinders in a tilted position ； 58. Inadequate fixation when assembling or adjusting large workpieces ； 59. Failing to clean the work site promptly after work is done ； 60. After finishing work at heights, store items on the lifting platform ； 61. When carrying out cross-task operations, do not communicate with other workers ； 62. Lifting heavy objects of over 50 kilograms by oneself ； 63. When two or more people are lifting a heavy object, their commands are not in sync ； 64. Crossing the load-bearing steel cables ； 65. Use an illumination voltage higher than 12 volts when working inside pressure vessels ； 66. Entering a small, enclosed compartment to work without supervision ； 67. Performing welding or gas cutting tasks outdoors in rainy conditions without taking any measures to prevent electric shock ； 68. Welding work in a sealed container without taking measures to prevent electric shock ； 69. Welding work is carried out in wet areas without any measures to prevent electric shock ； 70. Leaving one’s post without permission while performing guardianship duties ； 71. Use scrapped equipment and tools ； 72. Using tools with security flaws ； 73. Overloading mechanical equipment ； 74. Inadequate observation during lifting operations and unclear command signals ； 75. Standing on the lifted load to direct the lifting operation ； 76. Using lifting equipment beyond its capacity ； 77. The objects being lifted during lifting operations are not secured properly ； 78. Installing temporary power supply lines without permission ； 79. Facing the operation of electrical switches to turn power on and off ； 80. Performing repairs and maintenance on electrical equipment while it is still powered on ； 81. The return circuit for welding operations is not connected properly ； 82. Installing fixed lighting fixtures that use non-safe voltage for power supply in production areas without authorization ； 83. Driving at excessive speed (10 km/h) within a plant area that is not a special vehicle factory ； 84. The welder fails to connect the welding machine to the ground for protection ； 85. The power supply to electrical equipment was not turned off in a timely manner after work was completed ； 86. Failing to turn off the gas supply in time after using gas welding and cutting equipment ； 87. Unauthorized use of fire in no-fire zones ； 88. Leaving items scattered about hinders fire prevention and escape routes ； 89. Performing welding or heating operations carelessly without understanding the conditions around the work area ； 90. Conducting welding or heating work recklessly in the presence of a fire or other **hazards ； 91. Perform welding and cutting operations on small barrel-shaped containers of unknown origin ； 92. Performing welding or cutting operations on pipes and containers under pressure without caution ； 93. Using gas-cutting soft tape without following the specified color codes ； 94. Use oxygen for ventilation ； 95. Smoking on ships ； 96. Failing to remove any remaining embers promptly after hot work is completed ； 97. Piling up objects around key areas such as fire hydrants and fire extinguishers ； 98. Use water or foam extinguishers to put out electrical fires that have not yet been powered off ； 99. Storing flammable and explosive materials under electrical switches ； 100. Storing hazardous substances such as fuel without permission.