On the topic of \"Compilation of Standards for Plastic Pipes (Product Volume)\\"
Thread Content
On the topic of \"Compilation of Standards for Plastic Pipes (Product Volume)\": Book title: Compilation of Standards for Plastic Pipes (Product Volume); Author: Second Editing Department, China Standard Press; Publisher: China Standard Press; Publication date: May 2010. Introduction: Plastic pipes are favored in the pipeline engineering industry due to their lightweight nature, corrosion resistance, low water flow loss, and ease of installation. Compared to traditional metal pipes, plastic pipes require less energy for production and cause less environmental pollution, which has led to increasing attention from ** and related industries. Over the past 10 years, China’s plastic pipe industry has developed at an extremely rapid pace; currently, its production volume is second in the world, only behind that of the United States. The application areas of plastic pipes have expanded to various sectors such as construction, municipal services, communications, industry, and agriculture. China’s plastic pipeline technology continues to innovate in all aspects, from basic theories to product standards and testing standards. All stages of plastic pipe production should be carried out in accordance with standards, and the role of these standards in production must be continuously strengthened. To further address the practical difficulties faced by relevant manufacturing enterprises, research institutions, and other organizations, such as the lack of standards and incomplete standard collections, China Standards Press has specially compiled the \"Compilation of Plastic Pipe Standards\", which is divided into product volumes and test method volumes. This book is the \"Compilation of Standards for Plastic Pipes – Product Volume\", which gathers the **standards** related to plastic pipes that were issued by the end of January 2010; in total, there are 61 such standards and 1 standard amendment. These include product standards for polyvinyl chloride pipes, polyethylene pipes, polypropylene pipes, polybutylene pipes, thermoplastics, aluminum-plastic composite pipes, and other similar products. I. Since the publication of this Standard Compilation, 2 standards have been revised: GB 15558.1-2015 Buried polyethylene (PE) piping systems for gas – Part 1: Pipes (replacing GB 15558.1-2003); GB/T 21238-2016 Glass fiber reinforced plastic sand-filled pipes (replacing GB/T 21238-2007). II. The author has attached the table of contents of the Plastic Piping Standards Compilation (Product Volume) for the benefit of all readers
This post was last edited by nj1952 on 2017-6-25 at 12:59. Table of Contents of “Compilation of Plastic Pipe Standards (Product Volume)”
Part I: Basic Standards
GB 7231-2003 – Basic identification colors, identification symbols, and safety markings for industrial pipes
GB/T 14811-2008 – Terms related to heat pipes
GB/T 19278-2003 – General terms and definitions for thermoplastic pipes, fittings, and valves
Part II: Polyvinyl Chloride Pipes
GB/T 4219.1-2008 – Industrial rigid polyvinyl chloride (PVC-U) pipe systems – Part 1: Pipes
GB/T 4219.2-2015 – Industrial rigid polyvinyl chloride (PVC-U) pipe systems – Part 2: Fittings
GB/T 5836.1-2006 – Rigid polyvinyl chloride (PVC-U) pipes for building drainage
GB/T 5836.2-2006 – Rigid polyvinyl chloride (PVC-U) fittings for building drainage
GB/T 10002.1-2006 – Rigid polyvinyl chloride (PVC-U) pipes for water supply
GB/T 10002.2-2003 – Rigid polyvinyl chloride (PVC-U) fittings for water supply
GB 10010-2009 – Medical flexible polyvinyl chloride pipes
GB/T 13664-2006 – Rigid polyvinyl chloride (PVC-U) pipes for low-pressure water delivery and irrigation
GB/T 16800-2008 – Core-foamed rigid polyvinyl chloride (PVC-U) pipes for drainage
GB/T 18477.1-2007 – Rigid polyvinyl chloride (PVC-U) structural-wall pipe systems for buried drainage – Part 1: Double-wall corrugated pipes
GB/T 18477.2-2011 – Rigid polyvinyl chloride (PVC-U) structural-wall pipe systems for buried drainage – Part 2: Reinforced pipes
GB/T 18477.3-2009 – Rigid polyvinyl chloride (PVC-U) structural-wall pipe systems for buried drainage – Part 3: Double-layer axially hollow-wall pipes
GB/T 18993.1-2003 – Chlorinated polyvinyl chloride (PVC-C) pipe systems for cold and hot water – Part 1: General provisions
GB/T 18993.2-2003 – Chlorinated polyvinyl chloride (PVC-C) pipe systems for cold and hot water – Part 2: Pipes
GB/T 18993.3-2003 – Chlorinated polyvinyl chloride (PVC-C) pipe systems for cold and hot water – Part 3: Fittings
GB/T 18998.1-2003 – Industrial chlorinated polyvinyl chloride (PVC-C) pipe systems – Part 1: General provisions
GB/T 18998.2-2003 – Industrial chlorinated polyvinyl chloride (PVC-C) pipe systems – Part 2: Pipes
GB/T 18998.3-2003 – Industrial chlorinated polyvinyl chloride (PVC-C) pipe systems – Part 3: Fittings
GB/T 20221-2006 – Rigid polyvinyl chloride (PVC-U) pipes for non-pressure buried sewage and drainage
GB/T 24452-2009 – Chlorinated polyvinyl chloride (PVC-C) pipes and fittings for sewage and wastewater (high/low temperature) in buildings
Part III: Polyethylene Pipes
GB/T 13663-2000 – Polyethylene (PE) pipes for water supply
GB/T 13663.2-2005 – Polyethylene (PE) pipe systems for water supply – Part 2: Fittings
GB 15558.1-2015 – Buried polyethylene (PE) pipe systems for gas – Part 1: Pipes
GB 15558.2-2005 – Buried polyethylene (PE) pipe systems for gas – Part 2: Fittings
GB 15558.3-2008 – Buried polyethylene (PE) pipe systems for gas – Part 3: Valves
GB/T 18992.1-2003 – Cross-linked polyethylene (PE-X) pipe systems for cold and hot water – Part 1: General provisions
GB/T 18992.2-2003 – Cross-linked polyethylene (PE-X) pipe systems for cold and hot water – Part 2: Pipes
GB/T 19472.1-2004 – Polyethylene (PE) structural-wall pipe systems for burial – Part 1: Polyethylene double-wall corrugated pipes
GB/T 19472.2-2004 – Polyethylene (PE) structural-wall pipe systems for burial – Part 2: Polyethylene spiral-wound structural-wall pipes
GB/T 19796-2005 – Plastic saddles for polyethylene pressure pipes used in agricultural irrigation equipment
GB/T 19807-2005 – Preparation of composite specimens for polyethylene pipes and fittings and electrofusion fittings
GB/T 19809-2005 – Preparation of electrofusion joint assemblies for polyethylene (PE) pipes/pipes or pipes/fittings
GB/T 20201-2006 – Mechanically connected fittings for polyethylene (PE) pressure pipes used in irrigation
GB/T 20674.1-2006 – Welding equipment for polyethylene systems in plastic pipes and fittings – Part 1: Electrofusion joining
GB/T 20674.2-2006 – Welding equipment for polyethylene systems in plastic pipes and fittings – Part 2: Fusion splicing
GB/T 22051-2008 – Slip-on compression-type pipe fittings for cross-linked polyethylene (PE-X) pipes
GB/T 24456-2009 – High-density polyethylene pipes with silicon cores
Part I: Basic Standards
GB 7231-2003 – Basic identification colors, identification symbols, and safety markings for industrial pipes
GB/T 14811-2008 – Terms related to heat pipes
GB/T 19278-2003 – General terms and definitions for thermoplastic pipes, fittings, and valves
Part II: Polyvinyl Chloride Pipes
GB/T 4219.1-2008 – Industrial rigid polyvinyl chloride (PVC-U) pipe systems – Part 1: Pipes
GB/T 4219.2-2015 – Industrial rigid polyvinyl chloride (PVC-U) pipe systems – Part 2: Fittings
GB/T 5836.1-2006 – Rigid polyvinyl chloride (PVC-U) pipes for building drainage
GB/T 5836.2-2006 – Rigid polyvinyl chloride (PVC-U) fittings for building drainage
GB/T 10002.1-2006 – Rigid polyvinyl chloride (PVC-U) pipes for water supply
GB/T 10002.2-2003 – Rigid polyvinyl chloride (PVC-U) fittings for water supply
GB 10010-2009 – Medical flexible polyvinyl chloride pipes
GB/T 13664-2006 – Rigid polyvinyl chloride (PVC-U) pipes for low-pressure water delivery and irrigation
GB/T 16800-2008 – Core-foamed rigid polyvinyl chloride (PVC-U) pipes for drainage
GB/T 18477.1-2007 – Rigid polyvinyl chloride (PVC-U) structural-wall pipe systems for buried drainage – Part 1: Double-wall corrugated pipes
GB/T 18477.2-2011 – Rigid polyvinyl chloride (PVC-U) structural-wall pipe systems for buried drainage – Part 2: Reinforced pipes
GB/T 18477.3-2009 – Rigid polyvinyl chloride (PVC-U) structural-wall pipe systems for buried drainage – Part 3: Double-layer axially hollow-wall pipes
GB/T 18993.1-2003 – Chlorinated polyvinyl chloride (PVC-C) pipe systems for cold and hot water – Part 1: General provisions
GB/T 18993.2-2003 – Chlorinated polyvinyl chloride (PVC-C) pipe systems for cold and hot water – Part 2: Pipes
GB/T 18993.3-2003 – Chlorinated polyvinyl chloride (PVC-C) pipe systems for cold and hot water – Part 3: Fittings
GB/T 18998.1-2003 – Industrial chlorinated polyvinyl chloride (PVC-C) pipe systems – Part 1: General provisions
GB/T 18998.2-2003 – Industrial chlorinated polyvinyl chloride (PVC-C) pipe systems – Part 2: Pipes
GB/T 18998.3-2003 – Industrial chlorinated polyvinyl chloride (PVC-C) pipe systems – Part 3: Fittings
GB/T 20221-2006 – Rigid polyvinyl chloride (PVC-U) pipes for non-pressure buried sewage and drainage
GB/T 24452-2009 – Chlorinated polyvinyl chloride (PVC-C) pipes and fittings for sewage and wastewater (high/low temperature) in buildings
Part III: Polyethylene Pipes
GB/T 13663-2000 – Polyethylene (PE) pipes for water supply
GB/T 13663.2-2005 – Polyethylene (PE) pipe systems for water supply – Part 2: Fittings
GB 15558.1-2015 – Buried polyethylene (PE) pipe systems for gas – Part 1: Pipes
GB 15558.2-2005 – Buried polyethylene (PE) pipe systems for gas – Part 2: Fittings
GB 15558.3-2008 – Buried polyethylene (PE) pipe systems for gas – Part 3: Valves
GB/T 18992.1-2003 – Cross-linked polyethylene (PE-X) pipe systems for cold and hot water – Part 1: General provisions
GB/T 18992.2-2003 – Cross-linked polyethylene (PE-X) pipe systems for cold and hot water – Part 2: Pipes
GB/T 19472.1-2004 – Polyethylene (PE) structural-wall pipe systems for burial – Part 1: Polyethylene double-wall corrugated pipes
GB/T 19472.2-2004 – Polyethylene (PE) structural-wall pipe systems for burial – Part 2: Polyethylene spiral-wound structural-wall pipes
GB/T 19796-2005 – Plastic saddles for polyethylene pressure pipes used in agricultural irrigation equipment
GB/T 19807-2005 – Preparation of composite specimens for polyethylene pipes and fittings and electrofusion fittings
GB/T 19809-2005 – Preparation of electrofusion joint assemblies for polyethylene (PE) pipes/pipes or pipes/fittings
GB/T 20201-2006 – Mechanically connected fittings for polyethylene (PE) pressure pipes used in irrigation
GB/T 20674.1-2006 – Welding equipment for polyethylene systems in plastic pipes and fittings – Part 1: Electrofusion joining
GB/T 20674.2-2006 – Welding equipment for polyethylene systems in plastic pipes and fittings – Part 2: Fusion splicing
GB/T 22051-2008 – Slip-on compression-type pipe fittings for cross-linked polyethylene (PE-X) pipes
GB/T 24456-2009 – High-density polyethylene pipes with silicon cores
This post was last edited by nj1952 on 2017-6-25 at 12:59.
Part 4: Polypropylene Pipes
GB/T 18742.1-2002 Polypropylene piping systems for hot and cold water – Part 1: General rules
GB/T 18742.2-2002 Polypropylene piping systems for hot and cold water – Part 2: Pipes
GB/T 18742.3-2002 Polypropylene piping systems for hot and cold water – Part 3: Fittings
Part 5: Polybutylene Pipes
GB/T 19473.1-2004 Polybutylene (PB) piping systems for hot and cold water – Part 1: General rules
GB/T 19473.2-2004 Polybutylene (PB) piping systems for hot and cold water – Part 2: Pipes
GB/T 19473.3-2004 Polybutylene (PB) piping systems for hot and cold water – Part 3: Fittings
Part 6: Thermoplastics
GB/T 4217-2008 Nominal outer diameter and nominal pressure of thermoplastic pipes for fluid transport
GB/T 10798-2001 General table of wall thicknesses for thermoplastic pipes
GB/T 10798-2001 Amendment 1 to the “General table of wall thicknesses for thermoplastic pipes”
GB/T 18475-2001 General classification and naming of materials for thermoplastic pressure pipes and fittings, as well as overall (design) coefficients
GB/T 18991-2003 Thermoplastic pipes and fittings for hot and cold water systems
GB/T 19993-2005 Test methods for thermal cycling of pipe and fitting combinations in polythermoplastic piping systems for hot and cold water
Part 7: Aluminum-Plastic Composite Pipes
GB/T 18997.1-2003 Aluminum-plastic composite pressure pipes – Part 1: Aluminum pipes with lap-welded aluminum-plastic joints
GB/T 18997.2-2003 Aluminum-plastic composite pressure pipes – Part 2: Aluminum pipes with butt-welded aluminum-plastic joints
Part 8: Others
GB/T 14382-2008 Three-way filters for pipes
GB/T 14823.2-1993 Special requirements for conduits used in electrical installations – Rigid insulating material flat conduits
GB/T 14823.4-1993 Special requirements for conduits used in electrical installations – Bendable, self-restoring insulating material conduits
GB/T 19647-2005 Plastic single-wall corrugated pipes for agricultural drainage
GB/T 19812.1-2005 Plastic products for water-saving irrigation – Part 1: Single-wing labyrinth drip irrigation tapes
GB/T 19812.2-2005 Plastic products for water-saving irrigation – Part 2: Pressure-compensating emitters and drip irrigation pipes
GB/T 19812.3-2008 Plastic products for water-saving irrigation – Part 3: Embedded drip irrigation pipes and tapes
GB/T 20207.1-2006 Acrylonitrile-butadiene-styrene (ABS) pressure piping systems – Part 1: Pipes
GB/T 20207.2-2006 Acrylonitrile-butadiene-styrene (ABS) pressure piping systems – Part 2: Fittings
GB/T 21238-2016 Glass fiber-reinforced plastic sand-filled pipes
Part 4: Polypropylene Pipes
GB/T 18742.1-2002 Polypropylene piping systems for hot and cold water – Part 1: General rules
GB/T 18742.2-2002 Polypropylene piping systems for hot and cold water – Part 2: Pipes
GB/T 18742.3-2002 Polypropylene piping systems for hot and cold water – Part 3: Fittings
Part 5: Polybutylene Pipes
GB/T 19473.1-2004 Polybutylene (PB) piping systems for hot and cold water – Part 1: General rules
GB/T 19473.2-2004 Polybutylene (PB) piping systems for hot and cold water – Part 2: Pipes
GB/T 19473.3-2004 Polybutylene (PB) piping systems for hot and cold water – Part 3: Fittings
Part 6: Thermoplastics
GB/T 4217-2008 Nominal outer diameter and nominal pressure of thermoplastic pipes for fluid transport
GB/T 10798-2001 General table of wall thicknesses for thermoplastic pipes
GB/T 10798-2001 Amendment 1 to the “General table of wall thicknesses for thermoplastic pipes”
GB/T 18475-2001 General classification and naming of materials for thermoplastic pressure pipes and fittings, as well as overall (design) coefficients
GB/T 18991-2003 Thermoplastic pipes and fittings for hot and cold water systems
GB/T 19993-2005 Test methods for thermal cycling of pipe and fitting combinations in polythermoplastic piping systems for hot and cold water
Part 7: Aluminum-Plastic Composite Pipes
GB/T 18997.1-2003 Aluminum-plastic composite pressure pipes – Part 1: Aluminum pipes with lap-welded aluminum-plastic joints
GB/T 18997.2-2003 Aluminum-plastic composite pressure pipes – Part 2: Aluminum pipes with butt-welded aluminum-plastic joints
Part 8: Others
GB/T 14382-2008 Three-way filters for pipes
GB/T 14823.2-1993 Special requirements for conduits used in electrical installations – Rigid insulating material flat conduits
GB/T 14823.4-1993 Special requirements for conduits used in electrical installations – Bendable, self-restoring insulating material conduits
GB/T 19647-2005 Plastic single-wall corrugated pipes for agricultural drainage
GB/T 19812.1-2005 Plastic products for water-saving irrigation – Part 1: Single-wing labyrinth drip irrigation tapes
GB/T 19812.2-2005 Plastic products for water-saving irrigation – Part 2: Pressure-compensating emitters and drip irrigation pipes
GB/T 19812.3-2008 Plastic products for water-saving irrigation – Part 3: Embedded drip irrigation pipes and tapes
GB/T 20207.1-2006 Acrylonitrile-butadiene-styrene (ABS) pressure piping systems – Part 1: Pipes
GB/T 20207.2-2006 Acrylonitrile-butadiene-styrene (ABS) pressure piping systems – Part 2: Fittings
GB/T 21238-2016 Glass fiber-reinforced plastic sand-filled pipes