On the topic of the \"Compilation of Standards for General Engineering Plastics\"
Thread Content
This post was last edited by nj1952 on 2017-6-24 at 14:56. Topic: Compilation of Standards for General Engineering Plastics. Book title: Compilation of Standards for General Engineering Plastics. Author: National Plastic Standardization Technical Committee. Publisher: China Standard Press. Publication date: August 2013. Introduction: Engineering plastics refer to polymer materials that can be used as structural materials, capable of withstanding mechanical stresses over a wide temperature range and functioning in relatively harsh physicochemical environments. With the rapid development of China’s national economy, the demand for engineering plastics in various industries across the country has grown swiftly. In particular, emerging industries as well as key industrial sectors and new areas of growth, such as electronics, automobiles, transportation, building materials, packaging, medical devices, and artificial organs, all require large quantities of engineering plastics with excellent properties. As a result, the demand for engineering plastics in China has increased dramatically in recent years. Driven by the development of industries such as automobiles and electronics, the demand for engineering plastics is expected to maintain a growth rate of around 5%, reaching approximately 11.46 million tons by 2015. The author attaches the table of contents of the \"Compilation of Standards for General Engineering Plastics\" here for the benefit of all netizens.
This post was last edited by nj1952 on 2017-6-24 at 14:56. Table of Contents of “Compilation of Standards for General Engineering Plastics”
I. General Methods
GB/T 1034-2008 Plastics – Determination of water absorption
GB/T 1040.1-2006 Plastics – Determination of tensile properties – Part 1: General rules
GB/T 1040.2-2006 Plastics – Determination of tensile properties – Part 2: Test conditions for molded and extruded plastics
GB/T 1040.3-2006 Plastics – Determination of tensile properties – Part 3: Test conditions for films and sheets
GB/T 1040.4-2006 Plastics – Determination of tensile properties – Part 4: Test conditions for isotropic and orthorhombic fiber-reinforced composites
GB/T 1041-2008 Plastics – Determination of compressive properties
GB/T 1043.1-2008 Plastics – Determination of impact properties of simply supported beams – Part 1: Non-instrumental impact testing
GB/T 1632.1-2008 Plastics – Determination of viscosity of polymer dilute solutions using capillary viscometers – Part 1: General rules
GB/T 1634.1-2004 Plastics – Determination of temperature of load deformation – Part 1: General test methods
GB/T 1634.2-2004 Plastics – Determination of temperature of load deformation – Part 2: Plastics, hard rubbers, and long-fiber reinforced composites
GB/T 1843-2008 Plastics – Determination of impact strength of cantilever beams
GB/T 2406.1-2008 Plastics – Determination of flammability by oxygen index method – Part 1: Guidelines
GB/T 2406.2-2009 Plastics – Determination of flammability by oxygen index method – Part 2: Room-temperature tests
GB/T 2408-2008 Plastics – Determination of burning properties: Horizontal and vertical methods
GB/T 2410-2008 Determination of light transmittance and haze of transparent plastics
GB/T 2918-1998 Plastics – Standard environment for conditioning of test specimens and testing
GB/T 3398.1-2008 Plastics – Determination of hardness – Part 1: Ball indentation method
GB/T 3398.2-2008 Plastics – Determination of hardness – Part 2: Rockwell hardness
GB/T 3682-2000 Determination of melt mass flow rate and melt volume flow rate of thermoplastic plastics
GB/T 9341-2008 Plastics – Determination of bending properties
GB/T 9345.1-2008 Plastics – Determination of ash content – Part 1: General methods
GB/T 16582-2008 Plastics – Determination of melting behavior (melting temperature or melting range) of partially crystalline polymers by capillary method and polarizing microscope method
GB/T 17037.1-1997 Preparation of injection-molded specimens from thermoplastic plastic materials – Part 1: General principles and preparation of universal specimens and rod specimens
GB/T 17037.3-2003 Plastics – Preparation of injection-molded specimens from thermoplastic plastic materials – Part 3: Small square specimens
GB/T 17037.4-2003 Plastics – Preparation of injection-molded specimens from thermoplastic plastic materials – Part 4: Determination of shrinkage upon molding
II. Polyamides
GB/T 6509-2005 Test method for low-molecular-weight content in polycaprolactam chips and fibers
GB/T 9345.4-2008 Plastics – Determination of ash content – Part 4: Polyamides
GB/T 12006.1-2009 Plastics – Polyamides – Part 1: Determination of viscosity
GB/T 12006.2-2009 Plastics – Polyamides – Part 2: Determination of water content
GB/T 12006.4-1989 Method for determination of boiling methanol extractables from polyamide homopolymers
HG/T 2235-1991 Method for determination of melting point of polyamides
HG/T 2349-1992 Polyamide 1010 resin
HG/T 2350-1992 Polyamide (PA) homopolymers for molding and extrusion – Nomenclature
I. General Methods
GB/T 1034-2008 Plastics – Determination of water absorption
GB/T 1040.1-2006 Plastics – Determination of tensile properties – Part 1: General rules
GB/T 1040.2-2006 Plastics – Determination of tensile properties – Part 2: Test conditions for molded and extruded plastics
GB/T 1040.3-2006 Plastics – Determination of tensile properties – Part 3: Test conditions for films and sheets
GB/T 1040.4-2006 Plastics – Determination of tensile properties – Part 4: Test conditions for isotropic and orthorhombic fiber-reinforced composites
GB/T 1041-2008 Plastics – Determination of compressive properties
GB/T 1043.1-2008 Plastics – Determination of impact properties of simply supported beams – Part 1: Non-instrumental impact testing
GB/T 1632.1-2008 Plastics – Determination of viscosity of polymer dilute solutions using capillary viscometers – Part 1: General rules
GB/T 1634.1-2004 Plastics – Determination of temperature of load deformation – Part 1: General test methods
GB/T 1634.2-2004 Plastics – Determination of temperature of load deformation – Part 2: Plastics, hard rubbers, and long-fiber reinforced composites
GB/T 1843-2008 Plastics – Determination of impact strength of cantilever beams
GB/T 2406.1-2008 Plastics – Determination of flammability by oxygen index method – Part 1: Guidelines
GB/T 2406.2-2009 Plastics – Determination of flammability by oxygen index method – Part 2: Room-temperature tests
GB/T 2408-2008 Plastics – Determination of burning properties: Horizontal and vertical methods
GB/T 2410-2008 Determination of light transmittance and haze of transparent plastics
GB/T 2918-1998 Plastics – Standard environment for conditioning of test specimens and testing
GB/T 3398.1-2008 Plastics – Determination of hardness – Part 1: Ball indentation method
GB/T 3398.2-2008 Plastics – Determination of hardness – Part 2: Rockwell hardness
GB/T 3682-2000 Determination of melt mass flow rate and melt volume flow rate of thermoplastic plastics
GB/T 9341-2008 Plastics – Determination of bending properties
GB/T 9345.1-2008 Plastics – Determination of ash content – Part 1: General methods
GB/T 16582-2008 Plastics – Determination of melting behavior (melting temperature or melting range) of partially crystalline polymers by capillary method and polarizing microscope method
GB/T 17037.1-1997 Preparation of injection-molded specimens from thermoplastic plastic materials – Part 1: General principles and preparation of universal specimens and rod specimens
GB/T 17037.3-2003 Plastics – Preparation of injection-molded specimens from thermoplastic plastic materials – Part 3: Small square specimens
GB/T 17037.4-2003 Plastics – Preparation of injection-molded specimens from thermoplastic plastic materials – Part 4: Determination of shrinkage upon molding
II. Polyamides
GB/T 6509-2005 Test method for low-molecular-weight content in polycaprolactam chips and fibers
GB/T 9345.4-2008 Plastics – Determination of ash content – Part 4: Polyamides
GB/T 12006.1-2009 Plastics – Polyamides – Part 1: Determination of viscosity
GB/T 12006.2-2009 Plastics – Polyamides – Part 2: Determination of water content
GB/T 12006.4-1989 Method for determination of boiling methanol extractables from polyamide homopolymers
HG/T 2235-1991 Method for determination of melting point of polyamides
HG/T 2349-1992 Polyamide 1010 resin
HG/T 2350-1992 Polyamide (PA) homopolymers for molding and extrusion – Nomenclature
This post was last edited by nj1952 on 2017-6-24 at 14:57.
III. Polyoxymethylene
GB/T 22271.1-2008 Plastics – Polyoxymethylene (POM) molded and extruded materials – Part 1: Nomenclature system and basis for classification
GB/T 22271.2-2008 Plastics – Polyoxymethylene (POM) molded and extruded materials – Part 2: Sample preparation and property determination
GB/T 22271.3-2016 Plastics – Polyoxymethylene (POM) molded and extruded materials – Part 3: General product requirements
HG/T 2233-1991 Copolyoxymethylene resin
HG/T 3604-1999 (2009) Determination of viscosity number and intrinsic viscosity number of polyoxymethylene resin solutions
IV. Polycarbonate
HG/T 2234-1991 Method for determining the viscosity number of polycarbonate solutions
HG/T 2503-1993 (2004) Polycarbonate resin
HG/T 3020-1999 (2009) Nomenclature for polycarbonate (PC) molded and extruded materials
V. Thermoplastic polyesters, polyphenylene ethers
GB/T 9345.2-2008 Determination of ash content in plastics – Part 2: Alkyl polyphthalates
GB/T 14189-2008 Fiber-grade polyester chips (PET)
GB/T 14190-2008 Test methods for fiber-grade polyester chips (PET)
GB 17931-2003 Polyethylene terephthalate (PET) resin for bottles
GB/T 24151-2009 Plastics – Glass fiber reinforced flame-retardant polybutylene terephthalate specialty material
GB/T 25255-2010 Test method for tensile properties of optical functional film polyethylene terephthalate (PET) films
HG 2001-1991 301-G30 Flame-retardant reinforced polybutylene terephthalate (PBT) engineering plastic
HG/T 2232-1991 Modified polyphenylene ether engineering plastic
HG 2361-1992 Nomenclature for polybutylene terephthalate (PBT) thermoplastic materials
VI. Polymethyl methacrylate
GB/T 7134-2008 Cast industrial plexiglass sheets
GB/T 15597.1-2009 Plastics – Polymethyl methacrylate (PMMA) molded and extruded materials – Part 1: Nomenclature system and basis for classification
GB/T 15597.2-2010 Plastics – Polymethyl methacrylate (PMMA) molded and extruded materials – Part 2: Sample preparation and property determination
VII. Acrylonitrile-butadiene-styrene (ABS)
GB/T 8661-2008 Determination of residual acrylonitrile monomer content in styrene-acrylonitrile copolymers in plastics – Gas chromatographic method
GB/T 12672-2009 Acrylonitrile-butadiene-styrene (ABS) resin
GB/T 16867-1997 (2004) Determination of residual styrene monomer in polystyrene and acrylonitrile-butadiene-styrene resins – Gas chromatographic method
GB/T 20417.1-2008 Plastics – Acrylonitrile-butadiene-styrene (ABS) molded and extruded materials – Part 1: Nomenclature system and basis for classification
GB/T 20417.2-2006 Plastics – Acrylonitrile-butadiene-styrene (ABS) molded and extruded materials – Part 2: Sample preparation and property determination
VIII. Polytetrafluoroethylene
HG/T 2899-1997 Nomenclature for polytetrafluoroethylene materials
HG/T 2900-1997 Test method for volume density of polytetrafluoroethylene resin
HG/T 2901-1997 Test method for particle size of polytetrafluoroethylene resin
HG/T 2902-1997 Polytetrafluoroethylene resin for molding
HG/T 2903-1997 Fine-particle polytetrafluoroethylene resin for molding
HG/T 2904-1997 Perfluoroalkoxyethylene resin for molding and extrusion
HG/T 3028-1999 Polytetrafluoroethylene resin for paste extrusion
III. Polyoxymethylene
GB/T 22271.1-2008 Plastics – Polyoxymethylene (POM) molded and extruded materials – Part 1: Nomenclature system and basis for classification
GB/T 22271.2-2008 Plastics – Polyoxymethylene (POM) molded and extruded materials – Part 2: Sample preparation and property determination
GB/T 22271.3-2016 Plastics – Polyoxymethylene (POM) molded and extruded materials – Part 3: General product requirements
HG/T 2233-1991 Copolyoxymethylene resin
HG/T 3604-1999 (2009) Determination of viscosity number and intrinsic viscosity number of polyoxymethylene resin solutions
IV. Polycarbonate
HG/T 2234-1991 Method for determining the viscosity number of polycarbonate solutions
HG/T 2503-1993 (2004) Polycarbonate resin
HG/T 3020-1999 (2009) Nomenclature for polycarbonate (PC) molded and extruded materials
V. Thermoplastic polyesters, polyphenylene ethers
GB/T 9345.2-2008 Determination of ash content in plastics – Part 2: Alkyl polyphthalates
GB/T 14189-2008 Fiber-grade polyester chips (PET)
GB/T 14190-2008 Test methods for fiber-grade polyester chips (PET)
GB 17931-2003 Polyethylene terephthalate (PET) resin for bottles
GB/T 24151-2009 Plastics – Glass fiber reinforced flame-retardant polybutylene terephthalate specialty material
GB/T 25255-2010 Test method for tensile properties of optical functional film polyethylene terephthalate (PET) films
HG 2001-1991 301-G30 Flame-retardant reinforced polybutylene terephthalate (PBT) engineering plastic
HG/T 2232-1991 Modified polyphenylene ether engineering plastic
HG 2361-1992 Nomenclature for polybutylene terephthalate (PBT) thermoplastic materials
VI. Polymethyl methacrylate
GB/T 7134-2008 Cast industrial plexiglass sheets
GB/T 15597.1-2009 Plastics – Polymethyl methacrylate (PMMA) molded and extruded materials – Part 1: Nomenclature system and basis for classification
GB/T 15597.2-2010 Plastics – Polymethyl methacrylate (PMMA) molded and extruded materials – Part 2: Sample preparation and property determination
VII. Acrylonitrile-butadiene-styrene (ABS)
GB/T 8661-2008 Determination of residual acrylonitrile monomer content in styrene-acrylonitrile copolymers in plastics – Gas chromatographic method
GB/T 12672-2009 Acrylonitrile-butadiene-styrene (ABS) resin
GB/T 16867-1997 (2004) Determination of residual styrene monomer in polystyrene and acrylonitrile-butadiene-styrene resins – Gas chromatographic method
GB/T 20417.1-2008 Plastics – Acrylonitrile-butadiene-styrene (ABS) molded and extruded materials – Part 1: Nomenclature system and basis for classification
GB/T 20417.2-2006 Plastics – Acrylonitrile-butadiene-styrene (ABS) molded and extruded materials – Part 2: Sample preparation and property determination
VIII. Polytetrafluoroethylene
HG/T 2899-1997 Nomenclature for polytetrafluoroethylene materials
HG/T 2900-1997 Test method for volume density of polytetrafluoroethylene resin
HG/T 2901-1997 Test method for particle size of polytetrafluoroethylene resin
HG/T 2902-1997 Polytetrafluoroethylene resin for molding
HG/T 2903-1997 Fine-particle polytetrafluoroethylene resin for molding
HG/T 2904-1997 Perfluoroalkoxyethylene resin for molding and extrusion
HG/T 3028-1999 Polytetrafluoroethylene resin for paste extrusion