【Q&A Question 045】2017.02.14
Thread Content
This post was last edited by 955559 on 2017-7-21 21:54. [Q&A Question No. 045] February 14, 2017: What are the requirements of the equipment regarding the use of lubricant filters? The reference answers will be visible after responding; points are awarded by identifying the key points. (Unless otherwise specified, all questions and answers are based on hydrogenation units.) ) A “three-stage” filtration system is required for lubricant filtration: large tank → portable tank → oil container → filling point. Petrochemical Area—“Creative Ideas for Energy Saving” event: http://bbs.hcbbs.com/thread-1666758-1-1.html The New Normal Cup—voting for the top 10 members of HaiChuan in 2016 is now underway; vote for the member you care about the most (please cast your valuable vote for the members in the Petrochemical Area). http://bbs.hcbbs.com/thread-1667649-1-1.html Summary thread of Q&A questions for 2017 (updates available now). http://bbs.hcbbs.com/thread-1657793-1-1.html Summary thread of daily questions for 2017 (updates available now). http://bbs.hcbbs.com/thread-1657794-1-1.html Summary thread of Q&A questions from 2016 (updates completed). http://bbs.hcbbs.com/thread-1597792-1-1.html Third-phase selection of outstanding management members at HaiChuan. http://bbs.hcbbs.com/thread-1655902-1-1.html Petrochemical Area—“Creative Ideas for Energy Saving” event: http://bbs.hcbbs.com/thread-1666758-1-1.html Xiaomi phones are up for grabs. Thread for collecting chemical industry technical materials in the “Petrochemical Section”. http://bbs.hcbbs.com/thread-1654603-1-1.html Many prizes are waiting for you (Source: HaiChuan Chemical Forum)
The filtration device must not be used incorrectly； Select filters appropriately
For the lubrication management of equipment, a three-stage filtration system should be employed, with attention to the following two points: First, the filtration devices must be used correctly. When using three-stage filters to purify lubricant, it is essential to select the appropriate filtration devices for each stage. In the first stage of filtration, the process takes place from the large oil tank to the white porcelain tank; in the second stage, it is from the white porcelain tank to the small oil jug; and in the third stage, it is from the small oil jug to the filling point. It is important to choose the right filtration device for each stage of filtration. II. Proper selection of filters: Different types of filters are used for the three-stage filtration of lubricating oil. A 60-mesh filter is used in the first stage, a 90-mesh filter in the second stage, and a 100-mesh filter in the third stage. Therefore, when filtering lubricating oil, it is necessary to use filters that are suitable for each stage in order to ensure an effective filtering result.
1. Inbound filtration: The oil must be strictly filtered when it is transported and stored in the oil tank via pumps. 2. Filtration during distribution: The oil must be filtered before being poured into the lubrication container. 3. Fuel filtration: The oil must be filtered before being introduced into the equipment’s fuel storage area.
Lubricant filtration requires a “three-stage” filtration process, namely from the large tank to the smaller tank, then to the oil container, and finally to the filling point.
Try to follow the \"five fixings\" and \"three filtrations\" system; the \"five fixings\" refer to fixing the location, quality, quantity, frequency, and responsible person. “The \"three filtrations\" refer to filtration upon the arrival of lubricating oil at the warehouse, filtration before it is distributed, and filtration during refilling. These are purification measures taken to reduce the amount of impurities in the oil and to prevent dust and other contaminants from entering the equipment along with the oil.
Different types of filtration devices should be used in combination for lubricants in order to reduce mechanical impurities in them and improve their cleanliness
Lubricant filtration requires a “three-stage” filtration process, namely from large drums to portable tanks to oil containers, and finally to the points where oil is applied.
The filtration requirements for lubricating oil require a “three-stage” filtration process, namely from large barrels → portable buckets → oil containers → filling points.