Rotating Equipment - English

Translations»English»Rotating Equipment

3915 topics · Page 1/40

#2129810Regarding the boundaries between project pre-commissioning/commissioning/start-up
#2043676Kaisibi hot water pump HPH model manual
#2778366Mouth ring gap
#1844260Problems with starting the centrifugal main fan
#1878079Questions about removing propane from York propane refrigeration systems?
#2934789Regarding the selection of centrifuges
#1760091Granulator maintenance
#1365198The centrifugal blower makes noise
#2350219The regenerated cycle gas compressor (reciprocating) after reconditioning exhibits high vibration
#1752023Changes in steam consumption for compressor turbines
#2293341Issues regarding the interlock alarm for the cooling water temperature of reciprocating compressor cylinders in winter
#1862364What kind of oil is generally used in the crankcase of oil-free reciprocating vacuum pumps?
#2789269Why is the back-pulse design used for bag dust collectors?
#2722258Fault diagnosis of large-scale units
#1874165Who can send the maintenance standards for a single-screw compressor?
#1889879Leaking packing in reciprocating hydrogen compressor
#2028930What pressure of inlet water is required for a water jet vacuum pump?
#1762358Meaning of digits and letters in turbines
#3101545Automatic conveying of ton bag materials, bag breaking, material feeding, and packaging collection device
#2326895Help: Measurement of the clearance in the crank arm of a reciprocating compressor. To what position does the dial indica
#1783247Automobile loading system
#2032890Polyethylene GEA ice machine
#2858820Classification of equipment into large, medium, and small sizes
#1825368The analysis results of the horizontal friction force on the spring bracket are abnormal
#1840876Rotating of mechanical equipment
#31218133D animation of the turbine installation process
#2767729Centrifugal Compressor Maintenance and Repair Procedures.doc
#2292105Regarding the issue of frequent start-stop cycles of the ice machine
#1763247The motor shaft on one unit has become thinner; is electroplating necessary?
#1840298The impact of the damper position in centrifugal fans on fan performance
#1665145Turbocharger lubricant foam problem
#3141191【Mechanical Equipment Technology Exchange Edition】Mechanical Equipment 【Daily Question】20201220
#2779981Centrifugal Compressor Maintenance Work Instruction Sheet.pdf
#1838985What type of mechanical seal and flushing scheme are suitable for high-temperature, viscous, flammable media?
#2880640Is there a substantial difference between the 212 mechanical seal and the 204 mechanical seal? What are the specific dif
#2777261How can static electricity in rotating equipment such as compressors and motors be eliminated?
#2221506Two fans share the same pipeline
#1806602Flushing and cooling of mechanical seals
#3139511How to determine between double mechanical seals and single mechanical seals
#1929250Which fluid dynamics equations are commonly used in analysis systems?
#2078810Wear of the thrust bearing in the piston compressor
#1911087. Rich gas compressor interstage condensate pump
#2216137Daily, one day 20181216
#2915933Reasons for the sudden increase in the leakage volume at the high-pressure end of the reforming cycle hydrogen compresso
#2022076Bearing temperature rising
#1769430New ideas for energy savings – “Creative thinking” for compressors’ energy efficiency
#2717803Backwashing of V-type filters
#2756774Sediment collection
#1911848Seeking “total heat recovery chillers””
#2014168Process gas compressor
#1657939Reciprocating compressor
#1933495Co-current and counter-current units of air coolers
#2072454Compressor dry start seal
#1917147Question: What are the reasons for the breakage of the piston rod in a piston compressor?
#1918615A Roots blower is a constant-flow blower; does it still maintain a constant flow even when the resistance is high? !
#2850017Centrifugal compressor
#2688051Can a quick-release valve be used in the control circuit of the anti-surge valve?
#2921447How should screw rotor pumps be protected during operation?
#2959003What are the methods to prevent wear on fans?
#1941181Why is a flow rate on the water side required for heat exchangers?
#1782585Is a check valve installed on the compressor anti-surge line?
#2817865【Mechanical Equipment Technology Exchange Edition】Mechanical Equipment 【Daily Question】20191017
#2278051Regarding the issue of startup oil for the cyclohydrogen compressor
#1972358The relationship between dynamic loads and static loads
#2260706What are the causes of vibration in fluorine-lined centrifugal pumps?
#3007622Air separation
#1980129Once the hydraulic unloading valve cylinder is opened, the valve stem moves forward by about ten centimeters
#2903958During these special times, I’m bored; let’s post a calibration issue for everyone to discuss
#1918331Centrifugal pumps are prone to producing abnormal noises
#1758364Must a nitrogen compressor be able to be placed outdoors?
#2226429Reciprocating machine stop point clearance
#2069717Exhaust fan
#3083343Piston compressor inlet flow rate
#1784232Why are support shims used instead of ordinary bearings in the booster of catalytic converters?
#2957427Discussion on issues related to the motor settings
#1854869Positioning method for the shaft sleeve of modular mechanical seals
#2070676Which companies around the world offer good remote monitoring and diagnostic systems for equipment?
#1769809Teaching you how to choose a suitable hydraulic jack
#1846163Seeking the user manual for the 2MCLl type rich gas compressor
#1851670Why is the minimum load for the stepless control system HycroCOM in reciprocating compressors only 20%?
#2752807What caused the motor of the shielded pump used for transporting methanol to burn out?
#3135037Questions about piston compressors
#2879418Could you recommend affordable brands of liquid metering pumps imported from Germany?
#1801437Selection of mixing mode
#2702443Seeking help regarding diaphragm compressor failures
#2914404What are the reasons for high exhaust pressure in condensing steam turbines?
#2849149How often do you change the lubricant or grease in your moving equipment?
#2890232Turbine model
#1977273Can the reducer have its speed increased using an inverter?
#2068092Bearings supplied by the new manufacturer – please explain what the letters and numbers in the picture mean
#1668117Electronic version of mechanical seal technology
#1888300High-speed pump
#2000051Regarding the destination of dry gas seal gas
#2048831How to set up a reciprocating compressor circuit
#1921034Turbine alignment
#1776429Issues with steam extraction from turbine condensers
#1811896Why are electric or pneumatic butterfly valves chosen for the inlet and outlet of compressors
#1774168Regarding the turning of the impeller cover plate
#1877187Compressor main seal gas
#2044319The packing seal of the reciprocating compressor is not tight enough

HCBBS Forum · Translations

Customer Service: service@hcbbs.com Backup: 21131350@qq.com