English — Forum #279 (Page 15/30)

1. How to simulate an oil cooler using EDR? - HCBBS Forum
2. Under the same equipment and pressure, which has greater power: superheated steam or saturated steam? - HCBBS Forum
3. Coking and blockage in serpentine tube heat exchangers - HCBBS Forum
4. Help: What exactly is the distance indicated by that specific measurement for the length of the heat exchanger? - HCBBS Forum
5. How to replace the coil inside a reaction kettle - HCBBS Forum
6. How to calculate the pressure drop at the U-bend of a U-tube heat exchanger - HCBBS Forum
7. Is the pressure difference on both sides at the moment of feed taken into account when calculating the thickness of the heat exchanger sectional baffle? - HCBBS Forum
8. Design of HTRI air coolers and shell-and-tube heat exchangers – Seeking expert advice - HCBBS Forum
9. For plate heat exchangers, what is the maximum allowable pressure difference between the cold and hot sides? - HCBBS Forum
10. Leakage at the sealing surface of the heat exchanger head - HCBBS Forum
11. What are the reasons for frequent internal leakage in the recirculating water heat exchangers used by marine enthusiasts? - HCBBS Forum
12. Design temperature of the saddle - HCBBS Forum
13. Comparison between twisted tubes and ordinary light tubes — Let numbers speak through calculations - HCBBS Forum
14. Regarding the graphite condenser matter - HCBBS Forum
15. Is there anything that can be used as a heat pipe exchanger for heat removal from reactors? - HCBBS Forum
16. Calculation method for the pressure resistance of stainless steel pipes - HCBBS Forum
17. Discussion on the support structure for the cooler core assembly - HCBBS Forum
18. How to design a universal press fitting tool for pipes with a diameter of 100 or less? - HCBBS Forum
19. Is it possible to use vertical six-meter heat exchange tubes without baffle plates? - HCBBS Forum
20. Channel arrangement program for plate-fin heat exchangers - HCBBS Forum
21. Seeking help regarding the enthalpy of steam and the heat of vaporization. - HCBBS Forum
22. Tube sheet calculation - HCBBS Forum
23. EDR error - HCBBS Forum
24. Acceptable criteria for the plasticity-free transition temperature of materials - HCBBS Forum
25. Flue gas cooling issue - HCBBS Forum
26. When calculating the expansion joint for SW6, how should the axial displacement required of the expansion joint be determined? - HCBBS Forum
27. Oxidative synthesis of glyphosate - HCBBS Forum
28. Regarding the selection of weld evaluation methods - HCBBS Forum
29. Heat exchange area - HCBBS Forum
30. Lansen Software Usage Issues Discussion Thread - HCBBS Forum
31. What causes a clogged exhaust condenser? - HCBBS Forum
32. Heat exchanger markings, calculation sheets, manuals, HTRI textbooks - HCBBS Forum
33. HTRI air cooler calculation overall coef, design/clean/actual - HCBBS Forum
34. Plate and shell heat exchanger design firm - HCBBS Forum
35. What is the difference between pressure tests and airtightness tests? - HCBBS Forum
36. Ask for help on the relationship between pressure drop and baffle spacing of tube coolers - HCBBS Forum
37. Calculation of heat exchanger expansion joints - HCBBS Forum
38. Calculation of expansion joints for fixed-tube-sheet heat exchangers - HCBBS Forum
39. Polymer-based non-metallic heat exchangers - HCBBS Forum
40. Online brush descaling technology: capable of 100% preventing and removing scaling in heat exchangers and condensers - HCBBS Forum
41. Seeking advice on ammonia evaporator issues - HCBBS Forum
42. Under what circumstances are openings made in the tube sheet for the vent and drain ports on the shell side of a heat exchanger generally permitted? - HCBBS Forum
43. Help: Does anyone have 3D animation files of heat exchangers (structural assembly)? Please share them! - HCBBS Forum
44. HTRI The heat loads calculated on the hot and cold sides are inconsistent. What’s going on? - HCBBS Forum
45. How to determine scaling in parallel heat exchangers - HCBBS Forum
46. Problems encountered in the use of anti-corrosion heat exchangers - HCBBS Forum
47. Is it necessary to feed circulating water when a circulating water cooler has been pressurized and will not be used for an extended period of time? - HCBBS Forum
48. How to estimate the outlet flow rate of a heat exchanger? - HCBBS Forum
49. Air-cooling delivery cycle - HCBBS Forum
50. Special flow meters for heat exchange stations from Shanghai Linxuan Instruments - HCBBS Forum
51. Seeking help with flue gas heat dissipation issues - HCBBS Forum
52. Seek expert advice——can negative-pressure, low-temperature steam be converted into high-pressure, high-temperature steam for use in heat exchangers? - HCBBS Forum
53. crystallizer - HCBBS Forum
54. How to calculate the properties of a mixed gas - HCBBS Forum
55. Surface inspection of the welding joint between the heat exchange tube and the composite tube sheet - HCBBS Forum
56. Wastewater heat exchanger - HCBBS Forum
57. On the first day of the new year, don’t forget to visit HaiChuan–where can I download the ASPEN software? - HCBBS Forum
58. Computational theories and methods for spray evaporation, drying, concentration, or granulation - HCBBS Forum
59. In GB28712, the number of heat exchange tubes is specified based on a square rotated by 45 degrees; are there values for other numbers of tubes such as 30 or 60? - HCBBS Forum
60. Stainless steel fin issues - HCBBS Forum
61. Newbie seeking advice: Calculation of heat exchange area for steel-aluminum composite fin heat exchangers - HCBBS Forum
62. Looking for manufacturers of flue gas condensation heat exchangers - HCBBS Forum
63. Compressor intercooler - HCBBS Forum
64. Consultation on cooling for recycled steam condensate - HCBBS Forum
65. Applications of heat pipes - HCBBS Forum
66. sw-6 calculation for 4-pass floating head flange - HCBBS Forum
67. Overall heat transfer coefficient of the heat exchanger - HCBBS Forum
68. Seek detailed energy consumption data for a 14 million KCal/h gas-fired heat transfer oil furnace - HCBBS Forum
69. I have a question about pressure drop - HCBBS Forum
70. Regarding the scope of application of NB/T 47018-2017 - HCBBS Forum
71. Seek drawings for 4 million kcal tubular furnace - HCBBS Forum
72. Heat exchange area of tube condenser - HCBBS Forum
73. The EDR and HTRI calculation results differ greatly; I don’t understand it~ - HCBBS Forum
74. Who has the QB/T1163-2000 standard for falling film evaporators? - HCBBS Forum
75. New type of rapid oil tank heater? ? ? - HCBBS Forum
76. For calculating heat exchangers using SW6 and the 4732 standard, how should the operating conditions be selected? - HCBBS Forum
77. What is the maximum unsupported span for such a heat exchanger? - HCBBS Forum
78. How to clean the tubes in the evaporator section that are blocked by scale - HCBBS Forum
79. Please help me see what selection software it is - HCBBS Forum
80. Seeking help with thermocouple-controlled heating! - HCBBS Forum
81. The classification of energy efficiency levels of plate heat exchangers will widen the gap between manufacturers - HCBBS Forum
82. Regarding gas-gas plate heat exchangers - HCBBS Forum
83. hrti 6.0 vmgthermo property data package - HCBBS Forum
84. Calculation of the flow area in the shell side of a shell-and-tube heat exchanger - HCBBS Forum
85. Announcement by the General Administration of Quality Supervision, Inspection and Quarantine on Repealing the Revised Safety Technical Specifications and Documents Related to Administrative Licenses for Special Equipment - HCBBS Forum
86. Looking for HTFS technical manuals or research reports - HCBBS Forum
87. Discussion on the issue of the condenser not performing heat exchange - HCBBS Forum
88. Does the air cooler tube bundle that has been in use for three years need to be pressurized with water? - HCBBS Forum
89. Refrigeration method of the refrigerant in an ice machine - HCBBS Forum
90. Internal leakage in plate heat exchanger - HCBBS Forum
91. Three effects and one concentration - HCBBS Forum
92. A question in SW6-2011 V3.1 patch three - HCBBS Forum
93. The air cooler is not performing well - HCBBS Forum
94. Conditions for exemption from calculation for eccentric connectors - HCBBS Forum
95. What does this symbol in the heat exchanger diagram mean? - HCBBS Forum
96. What is the groove depth value for the tube sheet side structure? - HCBBS Forum
97. Issues related to the condenser of vacuum reduced-pressure double-effect concentrators – feel free to discuss them. - HCBBS Forum
98. What’s causing this issue when importing PROII into HTRI? - HCBBS Forum
99. Selection of standards for heat exchangers - HCBBS Forum
100. Calculation problem of heat transfer coefficient of boiling surface in tube, what is the coefficient a in the formula - HCBBS Forum